![]() OpenSCAD provides two commands to create 3D solids from a 2D shape: linear_extrude() and rotate_extrude(). There is a few thing you cannot see if you look in the preview mode right after slicing.The text in its current form is incomplete.Įxtrusion is the process of creating an object with a fixed cross-sectional profile. So I'm using Cura version: 15.04.5, 2.3.1, 2.5.0, 3.6.0 and 4.6.1! Well I'm also using burtoogle's version of Cura found that the different versions may slice object differently depending of shape and form etc.Īlmost forgot your last question, I'll just zoom in from the outside of the model and using the gcode viewer (using the gcode file saved ready to print). This 3MF format is quite new (5-6 yr or something like that), so I'll "guess" there is some developing going on all the time.įor this reason I've tried and compared all the version there is and found my favourites. There are previous Cura versions that's makes 3MF files, which makes newer versions of Cura crash if you try loading these "old" 3MF files. Well, -the only difference here is the printer used.ĭuring the time since Cura geared up and introduced this "new" format into their slicer, things changed as this format have much more information about your object and your printer.įor this reason I'm using a few versions of Cura, even one of the oldest version to compare with. I've been looking at your "cut cone" when using the 3MF file of it with your setup. On another topic Tongeir - How do you get that fancy view in Cura. In the second file it constantly varies by layer going from a max of F2237.6 at layer 5 down to F600 at layer 498.Īll in all it doesn't seem possible that these were sliced with same software with near identical settings. In the first file it is consistent, layer by layer, at F1200. (The M106 line is because I had the fan set to step up speed by height.)Īnother thing is the feedrate. The one I did came in as yellow which is Mesh. The Gcode file of MinimalFort came in as red which is Outside Wall. When I have AutoCad read in a gcode file the color of the line is determined by words like "Mesh" or "Wall" or "Infill". G1 F2237.6 X112.554 Y53.106 Z1.201 E3897.33128Īs you can see, there are no G0 lines in the one I created and in fact there are none anywhere in the entire file. It is attached.ĮDIT: Here are some lines of code from MinimalFort's gcode file: Another thing is that the Gcode file you provided is 2.2MB and the file I generated is 4.1MB. 134mm for each jog and is consistent up the model. The same version of Cura should produce the same results. ![]() I don't understand why the one I sliced didn't do it. ![]() There is some easy way to improve the h stepping, this is to select from 8 bit to 16 bit stepping.īut this is perhaps a bit beyond this thread.Īll the short lines in the seam are about. Here is the start of the gradually climb in order to do spiraling without stop. Here is tree pictures from the gcode viewer at this critical start point (Using Cura 4.6.1): Those very first lines to be printed will indicate if this is a true spiralize mode. When checking printing in spiralized mod, I'll move the line bar all the way down, then starting play. I'm using the gcode viewer every time I'll print something new, I do not have make a test print if I'm using the filament brand I'm used to. The "h" mark is often caused by this little "back" movement. In spiralizer mode, the extruder shall move steady, without any stop, or stop -then a little back before starting move steady. This last point is important, cause it will give you an idea of how you printed object will look like. In here you will see the final result of your extruder, how it move and an indication of amount of filament that's used during travel. Layer height typically 0.1 mm (or extra fine 0.06 mm)Īnalyze your gcode file, -that's saved for printing. The most important setting I found to be set is: So, it is important to select the additional file types when installing Cura, normally you would have the default, but you will need to select 3mf and gcode as a minimum IMO. I've been using the spiralizer mode since Cura introduced it in their slicer, over time there have been some variants.įirst, if you like to analyze the gcode file, you need to use the file that's saved to be printed and not using the preview function after slicing your stc file!
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |